Material comparison

S235JR vs DC01: Compare the Ordered Material

S235JR is a designation in EN 10025-2 for hot-rolled structural products: S235 is the steel name and JR its quality. DC01 is a steel name in EN 10130 for cold-rolled flat products made for cold forming. Because the two come from different product standards, a quotation for one does not automatically answer an order for the other. This page compares what each order has to state, not which material is better, and leaves any change of material to a written design decision.

Scope of this comparison

Two different product standards. The rows list what each order has to state; they do not compare strength, chemistry or impact values and do not make either material an alternative to the other.

Chat on WhatsApp

Purpose

Structural use or cold forming

Specification

Standard, edition and full name

Condition

Form, delivery and surface

Approval

A written design decision

01 · Material purposes

Different Material Purposes

Start with the part, not the grade name. Ask whether the material carries load in a structure or is a cold-rolled flat product to be formed into a shape, and who owns that requirement on the drawing.

The two names belong to different product standards with different scopes. A drawing that calls for one of them has already chosen a product family, and a quotation for the other answers a different specification until the design owner decides otherwise.

  • S235JR in EN 10025-2

    Steel name S235 with quality JR, within the standard for hot-rolled non-alloy structural steel, as flat or long products. The structural design that names it sets the requirements the material has to meet.

  • DC01 in EN 10130

    A steel name within the standard for uncoated cold-rolled low-carbon flat products for cold forming. The forming process and part drawing decide which order conditions matter.

02 · Ordered specification

Compare the Ordered Specification

Ask each quotation to answer the same questions as your original order: which standard and edition, which complete designation, which product form and dimensions, which delivery condition, and which tests and inspection document. The table shows where each standard places those choices. A blank on either side is an open question for the offer, not a gap to fill with an assumption.

S235JR (EN 10025-2) vs DC01 (EN 10130)
AttributeS235JR (EN 10025-2)DC01 (EN 10130)Basis
Product standard and editionEN 10025-2:2019 covers hot-rolled non-alloy structural flat and long products. Structural hollow sections and tubes are outside its scope.EN 10130:2006 covers uncoated cold-rolled low-carbon flat products for cold forming. Narrow-rolled strip and products with their own standards are outside its scope.Scope clause of each standard; confirm which edition the drawing names.
Complete designationSteel name S235, quality JR and any applicable delivery-condition suffix.Product form, standard, steel name or number, surface quality and, where applicable, finish.Designation clause of each standard; a grade name alone is an incomplete order line.
Product form and dimensionsFlat or long product, with its dimensional standard and the dimensions ordered.Sheet, coil, slit coil or cut lengths, with the dimensions ordered.Scope and order-information clauses; no size range is implied.
Delivery conditionThe delivery-condition choices depend on the product form and are stated on the order.Skin-pass and oiling are order decisions; surface quality and surface finish are specified separately.Delivery-condition and surface clauses; record the condition of the actual offer.
Tests and inspection documentSelected tests or options and the inspection-document type. The JR quality is distinguished from the other S235 qualities by its specified impact-energy requirement.The tests specified for the order and the inspection-document type. Listed mechanical properties apply only under specified conditions.Purchase order and the actual document; a mill certificate records evidence and does not approve a change.
03 · Form and condition

Check Form and Condition

A matching steel name does not fix the physical item. A DC01 order can describe sheet, coil, slit coil or cut lengths; an S235JR order can describe a flat or a long product. A processed part made from either is a separate description again, with its own dimensions and condition.

A mill catalogue range describes what that mill lists. It is not a size, condition or delivery commitment from ZIVO STEEL, and it does not replace the conditions written into your order.

  • Physical form

    Name the form and dimensions on each side. If the drawing describes a cut or finished part, specify the purchased material and the part separately.

  • Delivery condition

    For S235JR, the delivery-condition options depend on the product form. For DC01, skin-pass and oiling are decided on the order.

  • Surface quality and finish

    For DC01, surface quality and surface finish are separate choices, and both are stated at enquiry and on the order.

  • Time before forming

    EN 10130 cautions that DC01 properties can change with storage. Tell the reviewer when the material will be formed.

04 · Substitution approval

Approve a Material Substitution

This is a review practice, not a clause of either standard. Treat a proposal to use DC01 where S235JR is specified, or the reverse, as a design change. No substitution is accepted because the names look close or because a certificate is attached.

  1. Original requirement

    Record the standard and edition, complete designation, form, dimensions, delivery condition, tests and inspection document from the original specification.

  2. Candidate specification

    Place the same fields for the proposed material beside the original, line by line, and mark every difference or gap.

  3. Batch evidence

    Attach the inspection document for the batch actually offered. It records material evidence; it does not by itself approve the change.

  4. Written decision

    Refer each difference to the person responsible for the original specification, and change the order only after that person approves it in writing.

05 · Material enquiry

Prepare the Material Enquiry

ZIVO STEEL is a steel supplier, not a mill. Set out the points below in the Your Inquiry field of the form on this page, including anything still undecided, so the request can be read against your exact specification. A quotation does not approve a change of material.

  • PurposeWhat the part does and which drawing or specification governs it.
  • SpecificationStandard and edition, complete designation, required tests and inspection-document type.
  • Form and sizeSheet, coil, slit coil, cut lengths or another form, with dimensions, delivery condition and surface.
  • Quantity and destinationThe quantity you need and where it is to be delivered.
  • Open questionsAny difference still awaiting design approval, and who will decide it.

Sources

  1. EN 10130:2006 Cold rolled low carbon steel flat products for cold forming — technical delivery conditions (SIST EN 10130:2007 preview)European Committee for Standardization; identical Slovenian adoption by SIST, preview hosted by iTeh · Accessed 2026-09-25
  2. EN 10025-2:2019 Hot rolled products of structural steels, Part 2 — final original-text preview (SIST EN 10025-2:2019)European Committee for Standardization; identical Slovenian adoption by SIST, preview hosted by iTeh · Accessed 2026-09-25
Get a quotation

Tell Us What You Need

Send the product form, grade, finish, thickness, width, length and quantity. Inquiries are answered within 2 hours.

Chat on WhatsApp
Send Inquiry

Send Your Inquiry

Name, email and your inquiry are all that is needed. Add a WhatsApp number if you prefer to chat.

Tell us what steel you need. You can include the grade, size, quantity or intended use if available.

Inquiries are answered within 2 hours.